Monday, November 2, 2015

...and all of a sudden, it was a car again...

As always, I apologize for the long delay between posts. It's been a very productive few months. I have been working almost nonstop since the last post, and the payoff has been huge.

When I last left off, I was preparing to replace the car's clutch - which I did.



When that was done, I reinstalled the transmission. While I still had plenty of room under the car, I replaced the brake lines - the rubber lines and the hard lines. I was reasonably sure the old hard lines would have been OK, but it was easy work and cheap insurance for my safety to do the extra work at this point.





Then I repainted the brake booster:


...and installed a new brake master cylinder as well as rebuilt calipers, new pads, and new rotors on all four corners:


Although I didn't get pictures, I also replaced the clutch hydraulics with new parts.

Around this time, the driveline also went back into the car. I put the driveshaft back in with fresh flex discs as well as a new center bearing and support. I also replaced the CV axles and repainted the differential:





Before buttoning-up the front end, I replaced the front shock absorbers, the steering damper, and the tie rods:

Before moving under the hood, I added a third brake light to the car and installed the long-absent trunk trim:


Finally, it was time to do some work under the hood. First, I popped off the valve cover to adjust the valvetrain and meanure timing chain stretch:

Then I removed the water pump and thermostat housing:

Then, it was off with the intake and exhaust manifolds to clean them up and replace the gasket:

Once that was done, the thermostat housing (with new thermostat) and new water pump went back on:

Pretty soon, the engine was buttoned-up again:

Then the new exhaust system went on:

At that point, I replaced the fuel primer pump and the underhood fuel lines:


...and before I knew it... THIS:

...became THIS:

The dust settled. What I'd begun three and a half years ago back in 2012 was done.















I actually got the car on the road two weeks ago. I've been driving it. As with any project of this length, it didn't come out perfect. I'm still finding and fixing little items along the way - nothing that's keeping the car off the road (not for long, anyway). But, I'm happy to be able to relax a bit now. It's been a very long few years, and I'm looking forward to enjoying this car.

For all of you who've read along, here's a test drive of the car:

Monday, July 6, 2015

Long delayed update on the Mercedes project

Apologies to anyone who has been reading along. I have been working on the car, and have kept the Youtube channel up to date, but the blog is almost five months behind.

After my last update, I finished installing all the car's trim, aside from the front end trim (waiting until I have the front end/engine work done.

After that, I pulled the driveshaft (which was challenging on its own) and did a complete rear suspension refresh (new shocks, new trailing arm bushings, new rear subframe mounts). Here are some highlights:




So, I'm deep into mechanical repairs. Now that the rear end is done and the driveshaft is out, I'm in the process of pulling the transmission so that I can replace the clutch:


At this point, I'm literally a few bolts away from having the transmission out of the car. Once it's out, the new clutch and associated components go in, at which point, I can reinstall the driveshaft and everything else under the car.

Tuesday, February 17, 2015

February update on the Mercedes

It doesn't feel like a month since my last update, but apparently it is. I've gotten more work done on the car, but not as much as I would have liked. Shortly after my last post, we started getting slammed with more snow than I've ever seen. Over the past month, this has turned into the worst winter I've ever seen. The frigid temperatures and the need to shovel snow have kept me busy. I've been in the garage, just not as much.

I did finish polishing out the paint. Although it's far from perfect, it turned out a lot better than I thought I'd be able to do on my own. I'm very happy with it. Once I was done with the paint job, I began installing exterior trim. Overall, the process has been moving along pretty quickly, aside from cleaning the trim pieces before installation.

As of now, I have both the driver and passenger side exterior trim installed. I still need to finish up the rear and front of the car, but once the trim is all installed, the cosmetic part of the project is done.